-
Step 1 — Find Out What The Customer Actually Wants
-
Step 2 — Do The LiFePO4 Charge Rate Math Before You Quote
-
Step 3 — Size The MPPT Against Reality, Not The Datasheet Ceiling
-
Step 4 — Pick The Right Victron Energy Lithium Battery, Not The First One You Find
-
Step 5 — Wire The SmartShunt Correctly Before You Trust The Readings
-
Step 6 — Run An Overnight Load Test Before Handoff
-
Step 7 — Save The Victron Energy Contact Info Before You Need It
-
Notes And Common Mistakes
I've been handling off-grid energy orders for 9 years. I've personally made and documented 6 significant errors, totaling roughly $3,900 in wasted budget. Now I maintain our team's checklist to prevent others from repeating my mistakes. This is that checklist.
Who this is for: installers and system integrators building commercial or mobile off-grid systems around Victron Energy lithium batteries. Especially if you're the one fielding customer questions like "how do I block EMF from my smart meter?" before they'll sign off on a design.
Seven steps. Order matters. Skipping steps 1 and 2 will cost you the most.
Step 1 — Find Out What The Customer Actually Wants
Most buyers focus on the inverter or battery capacity and completely miss the reason they're buying. That reason is sometimes weirder than you'd expect.
In 2023, a client asked us for a "fully off-grid Victron system." I quoted it. Standard stuff. Turned out — after two weeks of back and forth — that the customer didn't care about blackouts or power bills. They wanted to block EMF from smart meters. Their whole family had been convinced by what they'd read online. There was also a smart meter for water they wanted "disabled," which is not something any energy installer can actually do.
We ended up redesigning the whole thing. $1,200 of engineering time that a 20-minute conversation up front would have saved.
What to ask:
- What's the primary driver — grid independence, backup power, mobile operations, or reducing EMF exposure?
- If the answer is EMF: which meters specifically? Electric only, or also a smart meter for water? You can address the former with isolation and placement guidance; the latter is out of scope and out of your control.
- Which rooms does the equipment go in? EMF concerns shift with placement.
Note: I'm not here to argue whether the concern is founded. My job is making sure the system I spec does what the customer thinks it will.
Step 2 — Do The LiFePO4 Charge Rate Math Before You Quote
The question everyone asks is "how many amp-hours?" The question they should ask is "what's the C-rate, and does my solar array actually support it?"
LiFePO4 charge rate — for Victron energy lithium batteries or any LFP — is usually between 0.3C and 0.5C for continuous charging. Meaning a 200Ah battery wants 60–100A of available charge current to stay happy. If your customer's array can only deliver 40A on a good day, the battery will charge. Slowly. And "slowly" was not what they paid for.
Common mistake: spec the battery size first, then size the solar to "fit the roof." It's the other way around. The array drives the charge rate.
I did this in 2019. Quoted 200Ah of Victron lithium, sized the MPPT off the roof footprint, and delivered a system that took nearly 9 hours to charge from 20% state of charge. The customer had a datasheet showing 0.5C. We delivered roughly 0.2C. $640 to swap controllers plus a week of scheduling loss.
Checkpoint before quoting:
- Available array current = (panel W ÷ charge voltage) × 0.8 for losses
- Battery charge current capacity from the datasheet (0.3C–0.5C for LFP)
- The lower of the two is your real-world charge rate
Step 3 — Size The MPPT Against Reality, Not The Datasheet Ceiling
Victron's SmartSolar MPPT specs assume ideal conditions. Panels rarely hit ideal. On mobile and marine installs, expect 70–80% of rated output on a good day, and less than you'd like on a bad one.
Match MPPT PV input capacity to the array, then add at least 20% headroom. An MPPT rated for 100V input tied to a 95V array is asking for a hot-day clipping event. You'll get it. It won't happen on install day. It'll happen in July.
The 2021 error: I quoted a SmartSolar 100/30 against a small rooftop array that should've been on the 100/50. That $380 mistake taught me to calculate cold-weather Voc, not nominal. Sounds obvious in hindsight. Wasn't at the time.
Step 4 — Pick The Right Victron Energy Lithium Battery, Not The First One You Find
"Victron energy lithium battery" isn't a product. It's a category. Victron sells Smart Lithium, Lithium Superpack, and setups built around Lynx Smart BMS. They are not interchangeable. Different BMS requirements, different comms, different cabling.
Most buyers focus on price per kWh and completely miss the BMS infrastructure needed downstream. Quote Superpack, and you don't get CAN comms. Quote Smart Lithium, and you need an external BMS and cabling that adds 15–25% to the battery line item.
To be fair, Superpack is genuinely easier for small builds. But if the customer later wants monitoring or multi-battery management, you're ripping it out.
Step 5 — Wire The SmartShunt Correctly Before You Trust The Readings
This is the most common error I see from installers who otherwise know what they're doing. The SmartShunt goes on the negative battery terminal. Not the load side. Not the charger side. Everything else goes downstream of it. Everything.
I installed one in 2021 where the solar negative bypassed the shunt. It read state of charge in the customer's app for two months before they noticed the meter showed 80% while they had 45% capacity left. $380 in rework and a credibility hit I'm still annoyed about.
Checkpoint: after install, put a load on the system and watch the shunt's current reading. If it doesn't move, something's wired wrong. Simple.
Step 6 — Run An Overnight Load Test Before Handoff
The question everybody skips: does the system hold voltage under sustained load at the customer's real overnight ambient temperature?
Small LFP setups pull voltage sag differently at 40°F vs. 75°F. If you test during a mild afternoon and hand off, the customer's first cold night tells a different story than yours did.
2024 error: delivered a mobile unit in August. Customer's first cold-weather trip in October, the system shut down at a voltage that would've been fine at room temp. $470 rewire trip plus a lot of apologizing.
Step 7 — Save The Victron Energy Contact Info Before You Need It
This is the step I wish I'd added to the checklist years ago. The Victron Energy support page lists regional distributors, technical documentation, and warranty contacts. Most installers know this. What most installers don't do is save it to their phone before a customer calls at 6 pm on a Friday.
Not every distributor responds the same way. I don't have hard data on regional response times — just anecdotally, the EU distribution chain has always been faster for us than the US one. If you're a US-based installer handling victron energy contact queries, budget two to three business days for a written answer on anything non-emergency.
Exact contacts change by region and product line, so bookmark the manufacturer's page. Don't rely on a distributor email you got three years ago.
Notes And Common Mistakes
Things that trip people up even after going through the checklist:
- Don't promise "set and forget" for LFP. Batteries drift. BMS firmware updates. Someone has to look at the app once a month.
- Don't oversell the EMF angle. You can design a system that runs independent of the grid — that reduces reliance on grid power and grid meters. You cannot promise a customer their home is now EMF-free. Be honest about scope.
- Smart water meters are separate systems. You'll get asked to "disable" them. You can't. Say so in writing, early.
- LiFePO4 charge rate assumptions need updating every 18 months. What was best practice in 2022 may not apply in 2025. Cell chemistry and BMS recommendations have shifted. Read the current datasheet before every quote above $5k.
- A pre-check list doesn't replace experience. It saves the mistakes you can predict. The unpredictable ones are the expensive ones.
That's the checklist. If you use it and still get hit with a mistake, write it down. That's how the next version gets better.